Choose the ultrasonic welding frequency around the part and the horn, not by treating a higher kHz number as a better machine. Lower frequencies are generally considered for larger parts, while higher frequencies suit smaller, more delicate work. A small electronics cover and an automotive filter housing need different tooling reviews. If a long seam or a flexible wall prevents energy reaching the joint, changing frequency alone is not the answer.
Separate the numbers on the quotation
Frequency describes how often the system vibrates. Power describes a different part of its capability. Neither number, on its own, tells you whether a particular joint will weld, how much it will collapse or whether the visible surface will remain acceptable.
The table below lists the power options on the SHNEHP product page for the named frequency families. It is a catalogue reference, not a part-size limit or a ranking of weld quality.
| Published family | Listed model power options | Review with the part drawing |
|---|---|---|
| 15 kHz | 2600, 3500, 4500 and 6000 W | Horn coverage, joint area and whether the part transmits vibration to the seam |
| 20 kHz | 2000, 3000 and 4000 W | Contact face, material and the required joining result |
| 35 kHz | 800, 1200 and 1500 W | Access and support on a small part, with attention to cosmetic surfaces |
There is no universal length or wall-thickness cutoff in that table. Selecting a family does not remove the need to design a horn for the actual contact surface. A larger power rating cannot make an unsuitable joint accessible.
Put the horn on the drawing before choosing a family
For a small ABS electronics enclosure, mark the surface that the horn will touch and the seam under it. Check whether the lid locates on the body before the horn applies pressure. The frequency discussion is useful only after there is a supported path from that contact surface to the joint.
A deeper filter housing raises a different question. If the seam is far from the horn face, some materials transmit the vibration poorly along that route. Semi-crystalline plastics such as PP and PA need more care with joint design and horn-to-joint distance than amorphous materials such as ABS. A frequency label does not compensate for a poorly supported sidewall or a joint that receives too little motion.
For a large automotive housing, review whether ultrasonic welding is suitable at all. Horn size limits the area that can be addressed, and a long seam may be a better job for vibration or hot plate welding. Do not choose the lowest frequency just to keep a large part on an ultrasonic machine.
What to compare in a part trial
Keep the resin grade, molded-part version and acceptance requirements the same. Then record the proposed frequency, horn, fixture and settings with each result. If several of these change together, a better sample does not show that the frequency alone caused the improvement.
Look at both sides of the decision. Does the seam meet the required retention or sealing check? Does the horn leave an unacceptable mark, or does the part distort? A cover that looks clean but has an incomplete joint is not an acceptable result. Nor is a strong joint enough if the mating dimensions have moved outside the drawing requirement.
Amplitude, pressure and weld termination also need review. They are not substitutes for frequency, and frequency is not a substitute for them. Time, energy and depth describe ways of controlling the weld, whereas kHz describes the vibration system. Compare a complete proposed process rather than a frequency in isolation.
Automatic frequency tracking is another separate term on a specification. It tracks the operating resonance of the system. It should not be read as a promise that one machine can switch between the 15, 20 and 35 kHz families without a different system configuration.
Ask for a part-based proposal
SHNEHP offers the published 15, 20 and 35 kHz ultrasonic ranges, with custom horns, boosters and fixtures. The inquiry should include the assembled and separate part drawings, resin grade, visible surfaces, joint requirements and target cycle. If a machine is already installed, include its frequency and tooling details rather than asking for a replacement horn by part size alone.
We can weld samples free of charge using your own parts. Use the samples to confirm the proposed machine and tooling together, before treating a catalogue frequency as a production decision.
Websites: shnehp.com | shnehp.cn
Request a Technical Consultation
Send your part drawing, sample information, plastic material and target cycle time. Our engineers will recommend a practical hot plate welding machine configuration.
Information in this article is taken from: /ultrasonic-welding-machine/

